Steel may need additional heat at different points in production, but not always for the same reason. Before the finishing stands, a hot transfer bar may need its temperature profile corrected for rolling. In a strip processing line, heating supports operations such as drying or annealing. These induction heating applications share a physical principle, but serve different purposes.
How induction heating works
Alternating current in an inductor coil creates a changing magnetic field. The field induces circulating electrical currents, or eddy currents, in the steel. As these currents flow, the steel’s electrical resistance generates heat through the Joule effect. Heat is produced within the material rather than transferred from a burner flame or a heated surface.
The magnetic field does not determine the final temperature profile on its own. The inductor arrangement and its position relative to the steel influence where electrical power is first converted into heat. Heat then spreads through the material by conduction. The resulting temperature profile reflects both electromagnetic heating and thermal diffusion.
Electrical regulation adjusts the heating input as the product moves through the equipment. The required power depends on factors such as material dimensions, speed and the temperature increase to be achieved.
Induction heating before the finishing stands
In hot strip mills, a transfer bar is the hot, flat steel section moving toward the finishing stands, where the final hot-rolling reductions take place. During transfer, the bar loses heat. Cooling is not uniform: temperatures may differ across its width, through its thickness and from head to tail. One average temperature cannot describe all these variations.
The edges are particularly exposed to heat losses through radiation and convection, so they tend to cool faster than the centre. Depending on the steel grade and rolling conditions, colder edges can contribute to uneven deformation, surface defects and additional trimming.
Edge Heating (EH): correcting colder edges
Rotelec’s Edge Heating (EH) concentrates the heating action near the two edges of the transfer bar. The induced currents raise the temperature where the loss is greatest, without applying the same correction across the full width. The heating profile can be adjusted to follow the edge-temperature deficit.
Inductor positioning and electrical control work together to provide the required correction while the bar moves. The equipment must also maintain suitable clearance around the material. This is important when bar dimensions or shape change during production.
Transverse Flux Heating (TFH): controlling a broader profile
Transverse Flux Heating (TFH) addresses a wider heating requirement across the transfer-bar section and along its length. In a transverse-flux arrangement, the magnetic flux crosses the bar, generally through its thickness. The resulting induced currents generate heat within the steel.
The electrical input can be adapted to bar thickness, speed and the target temperature rise (ΔT). When regulation is coordinated with the bar’s position and incoming thermal condition, it can also help reduce temperature differences between head and tail. The extent of that correction depends on operating conditions and the installed equipment and control strategy.
Induction heating in strip processing lines
In a strip processing line, the steel is already moving as continuous strip. Additional heat may be needed for drying or for a thermal treatment such as annealing. The target temperature and heating sequence are determined by the operation being performed.
In annealing, induction heating may provide one stage of a wider thermal cycle. Depending on the steel and the treatment route, the process may also require a holding period, controlled cooling and atmosphere management. Heating the strip is therefore only part of the complete treatment.
S-TFH: transverse-flux heating for continuous strip
Rotelec’s S-TFH solution uses transverse-flux induction for continuous-strip applications, including drying and annealing. It shares the heating principle of TFH, but works with strip moving through a processing line rather than a transfer bar approaching the finishing stands.
Its electrical settings can be adapted to strip speed, dimensions and the required temperature rise. The heating profile depends on the power delivered, how that power is distributed across the strip width and how long the material remains in the active heating zone. The detailed means used to control this distribution depend on the equipment configuration.
The heater must also operate as part of the line. Power conversion, electrical control, cooling and mechanical positioning are coordinated with strip movement and the surrounding equipment.
In summary
EH corrects localized temperature losses at transfer-bar edges. TFH provides broader transfer-bar heating and can support head-to-tail temperature equalization before the finishing stands. S-TFH heats continuous strip for operations in strip processing lines.
Each application uses induction to generate heat directly in steel. The achieved temperature profile depends on the thermal task, the operating conditions and how the equipment is configured and controlled.