TFH: Controlling Transfer-Bar Temperature from Head to Tail

A transfer bar does not enter the finishing mill all at once. The head, or leading end, arrives first, followed by the body and the tail. Each portion may need a different temperature correction before rolling. A suitable temperature at the head does not, by itself, establish the condition along the whole bar.

Rotelec’s Transverse Flux Heating (TFH) addresses this variation as part of the bar’s overall thermal condition. TFH temperature control combines heat generated directly within the steel with electrical regulation adapted to bar thickness, speed and the required temperature rise.

The objective is to compensate for temperature loss before the finishing stands and support more consistent rolling from head to tail. Because different portions of the bar may need different corrections, the heating input must follow the thermal requirement rather than remain at one fixed setting throughout the passage of the bar.

TFH temperature control starts from the required profile

Head-to-tail temperature equalization means reducing temperature differences along the bar’s length, in the direction of travel. It is distinct from equalization across the width or through the thickness. All three concern thermal uniformity, but they describe different directions within the material.

A higher average temperature does not necessarily mean a more uniform profile. Where the required correction varies along the bar, electrical regulation must account for that variation. Bar thickness and operating speed also affect the heating requirement, so they cannot be separated from the temperature target.

Within induction heating for hot strip mills, TFH is designed to improve temperature uniformity across the bar section and along its length. The correction takes place before the finishing stands, helping the mill receive steel in more consistent thermal conditions for rolling.

Two face-to-face inductors form a heating module

TFH uses two face-to-face inductors. Together they form a heating module that applies an alternating transverse magnetic flux (flux lines perpendicular to the bar surfaces) through the moving steel. That flux induces circulating electrical currents, or eddy currents, inside the bar.

As the induced currents flow, the steel’s electrical resistance produces heat. This conversion of electrical energy into thermal energy is the Joule effect. Heat is generated within the material rather than transferred to its surface from combustion burners.

Direct heat generation allows the heating input to respond to electrical regulation while the bar moves through the equipment. The TFH arrangement addresses the bar cross section, rather than concentrating the correction only in the two edge zones.

Why power must follow the temperature requirement

The required temperature increase is commonly written as Delta T (ΔT). It describes the rise needed to bring the material toward the target temperature before rolling. The heating input must be regulated for that requirement, rather than selected solely from the equipment’s maximum power rating. Installed power determines available capacity; the operating setting determines how that capacity is used.

Bar thickness and traveling speed also influence the heating requirement. A setting selected for one combination cannot simply be applied to every bar without considering the required temperature rise. The system has to regulate its output as these production conditions change.

TFH adjusts the power delivered to the inductor coils, through the converter output current and voltage, dynamically according to thickness, speed and target temperature rise. This links electrical input to the correction required by the moving steel. Rather than delivering one unchanged level of power, the system can adapt the supplied power as production conditions and thermal targets change.

This distinction also matters for energy use. A portion of a bar needing a smaller temperature increase does not call for the same thermal input as a comparable portion needing a larger one. Matching the supplied power to the required correction can help avoid unnecessary heating. It does not, on its own, prove a reduction in total electricity consumption: that must be assessed under actual production conditions, including the energy used by the complete heating installation.

Independent regulation supports head-to-tail equalization

TFH allows independent regulation of the power supplied to its inductors to support head-to-tail temperature equalization. The heating input is adjusted during the passage of the bar, in coordination with operating speed and the temperature target. Independent regulation helps align power delivery with the thermal requirement, but it remains part of a broader control strategy, not a substitute for it.

The difference between equal heating and equal temperature is important. Consider two otherwise comparable portions of a bar that need different temperature increases. Applying the same correction to both would not bring each to its target. The heating input must reflect the required rise for the portion being processed.

A rapid electrical response makes it possible to adjust the heating input as the bar passes. It does not, on its own, guarantee a uniform temperature. Head-to-tail control depends on combining that response with regulation suited to the bar’s dimensions, speed and required correction.

The aim is a more consistent temperature profile along the material entering the finishing mill. The selected configuration must be matched to the intended operating range, including the initial temperature profile, rather than relying on one power setting for every product.

Mechanical positioning and working clearance

The mechanical arrangement is part of the TFH system. Each of the two inductor cars carries an inductor and moves on rails. Hydraulic handling provides horizontal movement between parked and operating positions, together with vertical positioning for the bar thickness being processed.

This movement adapts the equipment position to the bar thickness while maintaining the required working clearance. The position of the inductors determines where the electromagnetic field acts on the moving steel, so the mechanical arrangement must be considered together with the electrical settings.

Integration into the mill must account for the operating position of the heating module, its movement to and from the parked position and the required clearance around the bar. These conditions define how the heating equipment fits into the existing production sequence.

Heating, power conversion, cooling and control work together

Medium-frequency converters supply the inductor coils. Programmable logic controllers (PLCs) and computer-based control coordinate automated operation. Dedicated cooling circuits keep the equipment within its required operating temperature range. Heating, power conversion and cooling must therefore be considered as parts of one operating system.

Each part has a defined function. The inductors generate the magnetic field; the electrical system supplies and regulates power; mechanical positioning establishes the working arrangement around the bar; cooling maintains suitable equipment temperatures. Their coordination is necessary for controlled, repeatable heating.

Rotelec’s TFH solution combines these functions in an integrated process system. The thermal objective, mill layout and production requirements determine its configuration. The inductor arrangement is one part of that configuration, alongside the power supply, control, cooling and mechanical interfaces with the mill.

How TFH differs from Edge Heating

Edge Heating (EH) corrects a localized problem: the transfer-bar edges lose temperature more rapidly than the central region. Its heating action is concentrated at those edges, with a profile shaped to compensate for that local deficit.

TFH addresses temperature uniformity across the bar section and along its length. Its face-to-face inductors and regulated electrical input support a broader heating requirement before the finishing mill, including the correction of head-to-tail temperature differences.

The distinction is one of application and equipment configuration, not of entirely different heating principles. EH also uses transverse magnetic flux to induce currents in steel. TFH is the name of the broader transfer-bar heating solution described here; transverse flux is not exclusive to that product.

Neither technology is a universal substitute for the other. The choice begins with the temperature distribution that needs correction and the operating conditions in which that correction must be achieved.

What temperature uniformity changes in rolling

A more uniform temperature profile gives the finishing stands more consistent material conditions. The intended benefits of TFH include improved elongation and more uniform mechanical properties across the rolled product. The thermal correction supports these results by improving the condition of the bar before rolling.

Thermal consistency can also support thickness control at thin final gauges, reduce work-roll wear and provide greater flexibility in rolling schedules. These are operational advantages of delivering steel closer to the intended temperature profile, not automatic consequences of installing more power. Their extent depends on the mill’s product range and operating conditions.

Performance assessment therefore starts with the application: which temperature deficit needs correction, over what range of bar dimensions and speeds, and for which rolling target? It should also establish whether the required temperature profile is achieved with the electrical input used under those conditions. Claims about lower consumption require comparison with an equivalent heating task and a clearly defined measurement boundary.

A heating system matched to the rolling requirement

TFH temperature control combines direct heat generation, regulated electrical input and equipment integrated with the mill. Together, these functions aim to deliver the required thermal correction, reduce temperature differences along the bar and improve the profile presented to the finishing stands. The value of regulation lies in matching heating input to the rolling objective, not in operating continuously at the equipment’s maximum capacity.

The distinction between transfer-bar and continuous-strip heating applications places TFH at a specific point in production: before the finishing mill. Its purpose is to correct the temperature of the solid transfer bar before the material undergoes the final hot-rolling reductions.

For a TFH assessment, the starting information is the range of bar dimensions, operating speeds, required temperature rise and available layout. These requirements define both the heating performance and the integrated equipment needed to deliver it under the mill’s operating conditions.

MENÙ